Electric hook-up (EHU) turns a tent, awning or caravan into a home from home: lights, a fridge, phone charging, even a kettle. But plug in too much and you’ll trip the site’s supply, usually just as dinner is cooking. Here’s how hook-up works in the UK and how to use it safely.
What is electric hook-up?
A hook-up pitch has a bollard with a blue, round, three-pin socket (a 16A industrial-style connector). You run a special outdoor cable from the bollard to your caravan, or to a mains unit if you’re in a tent, and get 230V mains electricity just like at home, but with a much lower limit on how much you can use at once.
The kit you need
- A hook-up cable: usually 25m long, with blue connectors at both ends. Choose a proper heavy-duty cable (2.5mm² is the common recommendation for a 25m lead).
- For tents: a camping mains unit with an RCD (residual current device) and normal UK sockets. Never run a domestic extension lead from the bollard.
- For caravans and motorhomes: the hook-up socket and consumer unit are already built in.
- Optional: a polarity tester, useful for European trips.
Understanding amps and watts
Campsites limit how much current each pitch can draw, measured in amps (A). Common supplies in the UK are:
- 16A: most modern sites
- 10A: common on older sites and abroad
- 5–6A: some small or older sites, and many in Europe
Appliances are rated in watts (W). To find out roughly how many amps something uses, divide the watts by 230:
Amps ≈ Watts ÷ 230
So a 3,000W domestic kettle uses about 13A, which would trip a 10A supply on its own. Here are typical figures:
| Appliance | Typical watts | Approx. amps |
|---|---|---|
| Domestic kettle | 2,000–3,000W | 9–13A |
| Low-wattage camping kettle | 750–1,000W | 3–4A |
| Hairdryer | 1,200–2,000W | 5–9A |
| Small electric heater (low setting) | 500–1,000W | 2–4A |
| Microwave (input power) | 1,000–1,300W | 4–6A |
| Caravan fridge on mains | ~125–200W | under 1A |
| Phone / laptop charger | 10–90W | under 0.5A |
| Caravan battery charger | ~100–300W | about 1A |
Always check the actual rating on your own appliances. Add up everything that could be on at the same time and keep it below the site’s limit.
Connecting up safely: the right order
- Make sure the caravan’s or mains unit’s switches are off.
- Unwind the whole cable, even if you only need a few metres. A coiled cable can overheat under load.
- Plug into the caravan or mains unit first.
- Then plug into the bollard, and turn the bollard switch on if there is one.
- Switch on at the caravan and test the RCD with its test button.
To disconnect, reverse the order: bollard first, then the caravan. That way the end you’re handling is never live.
Safety tips
- Lay the cable where it won’t be tripped over or driven over, and keep connectors off wet ground.
- Keep the mains unit off the groundsheet and away from where water might collect.
- Check the cable for damage before each trip, and replace it if the outer sheath is cut.
- Never use a domestic extension lead outdoors from the bollard.
- Never touch the bollard’s internal electrics. If the supply trips, ask the site staff to reset it.
What about polarity?
In the UK, site supplies should have correct polarity. Abroad, particularly in parts of Europe, reversed polarity is more common. It won’t stop things working, but it’s less safe. A simple polarity tester plugged into a caravan socket will tell you, and a short reversed-polarity adapter lead can correct it.
Don’t forget your battery
While you’re on hook-up, your caravan’s built-in charger keeps the leisure battery topped up. It’s worth knowing how your battery works for nights off-grid. See our leisure battery guide.
Know your amps, choose low-wattage appliances, and you’ll never be that pitch that keeps tripping the supply.
